Intel S845WD1-E Manuel d'utilisateur Page 60
- Page / 98
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Using the Setup Program
You can use the BIOS Setup program to change the configuration information and boot sequence
for the server. This chapter tells you how to access the BIOS Setup program and lists Setup
features, options, and default settings.
✏
NOTE
For reference purposes, you should write down the current Setup settings.
When you make changes to the settings, update this record.
BIOS Setup Program Modes
The BIOS Setup program has three modes of operation:
• Normal mode for normal operations
• Configure mode for clearing passwords (see Chapter 2 for instructions)
• Recovery mode for BIOS recovery
The BIOS Setup Program Operating mode is controlled by the setting of the configuration jumper
block. The jumper is set to normal mode at the factory.
✏
NOTE
The Setup menus described in this section apply to the server boards with
BIOS identifier WD845.10A.86B. Server boards with other BIOS identifiers
might have differences in some of the Setup menu screens.
The BIOS Setup program can be used to view and change the BIOS settings for the server. The
BIOS Setup program is accessed by pressing the <F2> key after the Power-On Self-Test (POST)
memory test begins and before the operating system boot begins. The menu bar is shown below.
Maintenance Main Advanced Security Power Boot Exit
Table 13. BIOS Setup Program Menu Bar
Maintenance Main Advanced Security Power Boot Exit
Clears
passwords and
Boot Integrity
Service (BIS)*
credentials, and
configures
extended
configuration
memory settings
Allocates
resources for
hardware
components
Configures
advanced
features
available
through the
chipset
Sets
passwords
and security
features
Configures
power
management
features
Selects boot
options and
power supply
controls
Saves or
discards
changes to
Setup
program
options
* For information about the BIS, refer to the Intel Web site at: http://developer.intel.com/design/security/index1.htm
60 Intel Server Board S845WD1-E Product Guide
- Server Board S845WD1-E 1
- Product Guide 1
- Disclaimer 2
- 2002 Intel Corporation 2
- Contents 3
- Contents v 5
- Figures 6
- Contents vii 7
- 1 Description 9
- Back Panel Connectors 10
- Front Panel Connectors 11
- Processors 13
- Intel 845E Chipset 14
- I/O Controller 15
- Diskette Drive Controller 16
- Keyboard and Mouse Interface 16
- Serial Ports 16
- Parallel Port 16
- ✏ NOTE 17
- Legacy USB Support 18
- PCI Auto Configuration 20
- PCI IDE Support 20
- BIOS Updates 21
- Recovering BIOS Data 22
- Boot Options 23
- Intel Rapid BIOS Boot 24
- BIOS Security Passwords 25
- Power Management Features 27
- Resume on Ring 28
- (Note 1) 29
- (Note 2) 29
- Wake-up Devices and Events 30
- Hardware Support 31
- Power Connector 32
- Fan Connectors 32
- LAN Wake Capabilities 32
- CAUTION 33
- Wake from USB 34
- Wake from PS/2 Devices 34
- PME# Wake-up Support 34
- PCI I/O Subsystem 35
- ATA-100 36
- Video Controller 37
- Video Memory Interface 38
- Hardware Monitoring 39
- Tools and Supplies Needed 41
- Before You Begin 41
- Warnings and Cautions 41
- DIMM Installation Guidelines 43
- Installing DIMMs 43
- Removing DIMMs 44
- Installing the I/O Shield 45
- Installing the Server Board 46
- Installing a Processor 47
- Removing the Processor 49
- Replacing the Battery 50
- WAARSCHUWING 51
- Connecting the IDE Cable 53
- Utility 55
- Creating Bootable Media 56
- Creating a Bootable Diskette 57
- Creating a BIOS Update Media 57
- Updating the BIOS 58
- Recovering the BIOS 59
- Using the Setup Program 60
- Maintenance Menu 61
- Maintenance 62
- Extended Configuration 62
- Main Menu 63
- Advanced Menu 64
- PCI Configuration Submenu 65
- Boot Configuration Submenu 66
- IDE Configuration Submenu 69
- Video Configuration Submenu 73
- Security Menu 74
- Power Menu 75
- Boot Menu 76
- Boot Device Priority Submenu 77
- Hard Disk Drives Submenu 78
- Removable Devices Submenu 78
- Exit Menu 79
- 4 Solving BIOS Problems 81
- BIOS Error Messages 82
- 5 Getting Help 85
- Server Board Connectors 87
- Server Board Resources 89
- I/O Map 90
- Interrupts 91
- Notes: 92
- Product Safety Compliance 93
- Product EMC Compliance 93
- FCC (USA) 94
- INDUSTRY CANADA (ICES-003) 95
- Installation Precautions 96
- Installation Requirements 97
Produits connexes et manuels pour Serveurs Intel S845WD1-E
Serveurs Intel TIGH2U Manuel d'utilisateur
(20 pages)
(20 pages)
Serveurs Intel SR9000MK4U Manuel d'utilisateur
(258 pages)
(258 pages)
Serveurs Intel Sx220 Manuel d'utilisateur
(150 pages)
(150 pages)
Serveurs Intel S5000PAL Manuel d'utilisateur
(16 pages)
(16 pages)
Serveurs Intel SR2500AL Manuel d'utilisateur
(210 pages)
(210 pages)
Serveurs Intel SR1680MV Manuel d'utilisateur
(196 pages)
(196 pages)
Serveurs Intel S3000AH Manuel d'utilisateur
(22 pages)
(22 pages)
Serveurs Intel SSR212PP Manuel d'utilisateur
(196 pages)
(196 pages)
Serveurs Intel SR1500AL Manuel d'utilisateur
(180 pages)
(180 pages)
Serveurs Intel SKA4 Manuel d'utilisateur
(136 pages)
(136 pages)
Serveurs Intel SR6850HW4 Manuel d'utilisateur
(119 pages)
(119 pages)
Serveurs Intel R1208WT2GS Spécifications
(104 pages)
(104 pages)
Serveurs Intel R2224GZ4GC4 Spécifications
(32 pages)
(32 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.864 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels