Intel T1700 Fiche technique Page 80
- Page / 98
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Package Mechanical Specifications and Pin Information
80 Datasheet
RESET# Input
Asserting the RESET# signal resets the processor to a known state and invalidates
its internal caches without writing back any of their contents. For a power-on
Reset, RESET# must stay active for at least two milliseconds after V
CC
and BCLK
have reached their proper specifications. On observing active RESET#, both FSB
agents deasserts their outputs within two clocks. All processor straps must be valid
within the specified setup time before RESET# is deasserted. There is a 55-Ω
(nominal) on die pull-up resistor on this signal.
RS[2:0]# Input
RS[2:0]# (Response Status) are driven by the response agent (the agent
responsible for completion of the current transaction), and must connect the
appropriate pins of both FSB agents.
RSVD
Reserved
/No
Connect
These pins are RESERVED and must be left unconnected on the board. However, it
is recommended that routing channels to these pins on the board be kept open for
possible future use.
SLP# Input
SLP# (Sleep), when asserted in Stop-Grant state, causes the processor to enter
the Sleep state. During Sleep state, the processor stops providing internal clock
signals to all units, leaving only the Phase-Locked Loop (PLL) still operating.
Processors in this state does not recognize snoops or interrupts. The processor
recognizes only assertion of the RESET# signal, deassertion of SLP#, and removal
of the BCLK input while in Sleep state. If SLP# is deasserted, the processor exits
Sleep state and returns to Stop-Grant state, restarting its internal clock signals to
the bus and processor core units. If DPSLP# is asserted while in the Sleep state,
the processor exits the Sleep state and transition to the Deep Sleep state.
SMI# Input
SMI# (System Management Interrupt) is asserted asynchronously by system logic.
On accepting a System Management Interrupt, the processor saves the current
state and enters System Management Mode (SMM). An SMI Acknowledge
transaction is issued and the processor begins program execution from the SMM
handler.
If an SMI# is asserted during the deassertion of RESET#, then the processor
tristates its outputs.
STPCLK# Input
STPCLK# (Stop Clock), when asserted, causes the processor to enter a low power
Stop-Grant state. The processor issues a Stop-Grant Acknowledge transaction, and
stops providing internal clock signals to all processor core units except the FSB and
APIC units. The processor continues to snoop bus transactions and service
interrupts while in Stop-Grant state. When STPCLK# is deasserted, the processor
restarts its internal clock to all units and resumes execution. The assertion of
STPCLK# has no effect on the bus clock; STPCLK# is an asynchronous input.
TCK Input
TCK (Test Clock) provides the clock input for the processor Test Bus (also known as
the Test Access Port).
TDI Input
TDI (Test Data In) transfers serial test data into the processor. TDI provides the
serial input needed for JTAG specification support.
TDO Output
TDO (Test Data Out) transfers serial test data out of the processor. TDO provides
the serial output needed for JTAG specification support.
TEST1, TEST2,
TEST3,
TEST4,
TEST5,
TEST6
Input
TEST1 and TEST2 must have a stuffing option of separate pulldown resistors to
V
SS
. For the purpose of testability, route the TEST3 and TEST5 signals through a
ground-referenced Zo=55 Ω trace that ends in a via that is near a GND via and is
accessible through an oscilloscope connection.
THRMDA Other Thermal Diode Anode.
THRMDC Other Thermal Diode Cathode.
Table 22. Signal Description (Sheet 6 of 7)
Name Type Description
- Dual-Core on 45-nm Process 1
- 2 Datasheet 2
- Contents 3
- 4 Datasheet 4
- Revision History 5
- 6 Datasheet 6
- 1 Introduction 7
- 1.1 Terminology 8
- 1.2 References 9
- Introduction 10
- 10 Datasheet 10
- 2 Low Power Features 11
- 2.1.1 Core Low-Power States 12
- Datasheet 13 13
- Low Power Features 13
- 2.1.2.4 Sleep State 14
- 2.1.2.6 Deeper Sleep State 15
- 2.1.2.5 Deep Sleep State 15
- 2.3 Low-Power FSB Features 16
- Datasheet 17 17
- 18 Datasheet 18
- 3 Electrical Specifications 19
- 3.5 Reserved and Unused Pins 22
- 3.7 FSB Signal Groups 23
- Table 4. FSB Pin Groups 24
- 3.8 CMOS Signals 25
- 3.9 Maximum Ratings 25
- Electrical Specifications 26
- 26 Datasheet 26
- Processors 28
- 4 Package Mechanical 33
- Specifications and Pin 33
- Information 33
- 34 Datasheet 34
- Datasheet 35 35
- 36 Datasheet 36
- Datasheet 37 37
- 38 Datasheet 38
- (Sheet 1 of 2) 39
- (Sheet 2 of 2) 40
- Datasheet 41 41
- 42 Datasheet 42
- Datasheet 43 43
- 44 Datasheet 44
- (Sheet 1 of 16) 45
- (Sheet 2 of 16) 45
- (Sheet 3 of 16) 46
- (Sheet 4 of 16) 46
- (Sheet 5 of 16) 47
- (Sheet 6 of 16) 47
- (Sheet 7 of 16) 48
- (Sheet 8 of 16) 48
- (Sheet 9 of 16) 49
- (Sheet 10 of 16) 49
- (Sheet 11 of 16) 50
- (Sheet 12 of 16) 50
- (Sheet 13 of 16) 51
- (Sheet 14 of 16) 51
- (Sheet 2 of 17) 53
- (Sheet 3 of 17) 53
- (Sheet 4 of 17) 54
- (Sheet 5 of 17) 54
- (Sheet 6 of 17) 55
- (Sheet 7 of 17) 55
- (Sheet 8 of 17) 56
- (Sheet 9 of 17) 56
- (Sheet 10 of 17) 57
- (Sheet 11 of 17) 57
- (Sheet 12 of 17) 58
- (Sheet 13 of 17) 58
- (Sheet 14 of 17) 59
- (Sheet 15 of 17) 59
- (Sheet 16 of 17) 60
- (Sheet 17 of 17) 60
- 74 Datasheet 74
- together with V 81
- 82 Datasheet 82
- 5 Thermal Specifications and 83
- Design Considerations 83
- 5.1.1 Thermal Diode 85
- 5.1.2 Thermal Diode Offset 87
- 5.1.3 Intel® Thermal Monitor 88
- 5.1.4 Digital Thermal Sensor 89
- 5.1.6 PROCHOT# Signal Pin 90
- Datasheet 91 91
- 92 Datasheet 92
- Datasheet 1 93
Produits connexes et manuels pour Processeurs Intel T1700
Processeurs Intel L5618 Fiche technique
(64 pages)
(64 pages)
Processeurs Intel B940 Fiche technique
(360 pages)
(360 pages)
Processeurs Intel AT80569KJ073N Fiche technique
(102 pages)
(102 pages)
Bosch GOP 10,8 V-LI Professional manuels
Manuels d'utilisation et guides de l'utilisateur pour Outils Bosch GOP 10,8 V-LI Professional.
Nous fournissons des manuels en pdf 1 Bosch GOP 10,8 V-LI Professional à télécharger gratuitement par type de document : Manuel de l'utilisateur
Bosch GOP 10,8 V-LI Professional Manuel de l'utilisateur (215 pages)
marque: Bosch | Catégorie: Tools | Taille: 14.52 MB |
Table des matières
Safety Notes
13
Assembly
15
Operation
18
Transport
20
Français
21
Operación
34
Português
36
Montagem
39
Italiano
44
Montaggio
47
Nederlands
51
Accu opladen
54
Montering
61
Ibrugtagning
63
Verktygsbyte
68
Driftstart
70
Igangsetting
76
Tuotekuvaus
80
Käyttöönotto
82
Ελληνικά
84
Λειτουργία
90
Akünün şarjı
95
Çalıştırma
97
Multi-Cutter
101
Dane techniczne
102
Wymiana narzędzi
103
Uruchamianie
105
Výměna nástroje
110
Pracovní pokyny
112
Slovensky
113
Výmena nástroja
117
Prevádzka
119
Údržba a servis
120
Műszaki adatok
123
Összeszerelés
124
Üzemeltetés
126
Українська
136
Початок роботи
142
AVERTISMENT
144
Date tehnice
147
Funcţionare
149
Български
152
Монтиране
155
Tehnički podaci
162
Promena alata
163
Puštanje u rad
164
Uputstva za rad
165
Slovensko
166
Tehnični podatki
169
Zamenjava orodja
169
Delovanje
171
Navodila za delo
172
Hrvatski
173
Zamjena alata
176
Upute za rad
178
Ohutusnõuded
180
Seadme osad
182
Aku laadimine
183
Tarviku vahetus
183
Tööjuhised
185
Latviešu
186
Pielietojums
188
Lietošana
192
Lietuviškai
194
Montavimas
197
Naudojimas
199
ﺔﻣﺪﺨﻟاو ﺔﻧﺎﻴﺼﻟا
201
ﻞﻐﺷ تﺎﻈﺣﻼﻣ
202
دﺪﻌﻟا لاﺪﺒﺘﺳا
204
ﻲﺑﺮﻋ
205
ءادﻷاو ﺞ
206
ﺘﻨﻤﻟا ﻒﺻو
206
نﺎﻣﻷا تﺎﻤﻴﻠﻌﺗ
207
ﺲﯾوﺮﺳ و ﺖﺒﻗاﺮﻣ
208
ﻰﺳرﺎﻓ
211
ﺖﻘﺑﺎﻄﻣ ﻪﯾرﺎﻬﻇا
212
راﺰﺑا ﺾﯾﻮﻌﺗ
212
هرﺎﮐ ﻪﻤﻫ
214
Plus de produits et de manuels pour Outils Bosch
| Modèles | Type de document |
|---|---|
| GSB 19-2 RE Professional |
Manuel de l'utilisateur
Bosch GSB 19-2 RE Professional User Manual,
172 pages
|
| GLI 14,4 V Professional |
Manuel de l'utilisateur
Bosch GLI 14,4 V Professional User Manual,
86 pages
|
| GTR 30 CE Professional |
Manuel de l'utilisateur
Bosch GTR 30 CE Professional User Manual,
256 pages
|
| GNA 16 (SDS) Professional |
Manuel de l'utilisateur
Bosch GNA 16 (SDS) Professional User Manual,
112 pages
|
| GCM 10 S Professional |
Manuel de l'utilisateur
Инструкция по эксплуатации Bosch GCM 10 S Professional,
266 pages
|
| GHP 8-15 XD Professional |
Manuel de l'utilisateur
Bosch GHP 8-15 XD Professional User Manual,
182 pages
|
| DWM 40 L Professional |
Manuel de l'utilisateur
Инструкция по эксплуатации Bosch DWM 40 L Professional,
82 pages
|
| PCL 10 |
Manuel de l'utilisateur
Bosch PCL 10 User Manual,
39 pages
|
| PLS 300 |
Manuel de l'utilisateur
Bosch PLS 300 User Manual,
130 pages
|
| S 500 A Professional |
Manuel de l'utilisateur
Bosch S 500 A Professional User Manual,
216 pages
|
| GluePen |
Manuel de l'utilisateur
Инструкция по эксплуатации Bosch GluePen,
66 pages
|
| AGS 7,2 LI |
Manuel de l'utilisateur
Bosch AGS 7,2 LI User Manual,
177 pages
|
| PPS 7S |
Manuel de l'utilisateur
Bosch PPS 7S User Manual,
537 pages
|
| Ciso |
Manuel de l'utilisateur
Инструкция по эксплуатации Bosch Ciso,
165 pages
|
| PTK 3,6 LI |
Manuel de l'utilisateur
Инструкция по эксплуатации Bosch PTK 3,6 LI,
240 pages
|
| PTA 2400 |
Manuel de l'utilisateur
Bosch PTA 2400 User Manual,
91 pages
|
| PKP 7,2 LI |
Manuel de l'utilisateur
Инструкция по эксплуатации Bosch PKP 7,2 LI,
122 pages
|
| DCN‑FET |
Manuel de l'utilisateur
Инструкция по эксплуатации Bosch DCN‑FET [es] ,
1 pages
|
| FAA‑500‑RTL |
Manuel de l'utilisateur
Инструкция по эксплуатации Bosch FAA‑500‑RTL,
2 pages
|
| GIM 60 L Professional |
Manuel de l'utilisateur
Bosch GIM 60 L Professional User Manual,
222 pages
|
© 2020, manymanuals.fr. Tous droits réservés | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels